CMC Rope Rescue Manual Practice Test

These questions are part of the practice quiz. Start practicing

• What are semi-rigid (Skedco) litters best used for?
• On which axis are carabiners strongest?
• What is the primary challenge of adding weight to your harness in a rescue situation?
• Why is it essential to tend the prusiks in a belay system?
• Which type of Brake Bar Rack provides more friction and control during descent?
• Why were early rescue pulleys inaccurately sized?
• Do you need to tie a knot at the anchor point to create a tensionless hitch?
• What does SSF stand for in rescue operations?
• How should you estimate the weight of hard rock for anchoring purposes?
• Once the highline is fully set up and the load is attached, which line is lowered to move the load out?
• What is the function of a litter insert?
• What does the Critical Point Analysis examine?
• Do you need to remove a swivel pulley from its carabiner to insert the rope?
• What is the term used for the bottom hole in a double pulley system?
• To which aspect does the concept of life safety rope primarily relate?
• Where should the medic be positioned during a low angle rescue involving multiple tenders?
• During low angle rescues, how can multiple tenders enhance the safety of the operation?
• What is the role of the "Tailer" in a rescue operation?
• What determines the size of a pulley?
• What characteristic defines a "Self Equalizing Anchor System"?
• What is critical to ensure before using any new rope?
• What is the minimum number of bars recommended for use on a brake bar rack?
• Which component is NOT typically part of a ratchet device?
• Can you wash carabiners with soap and water?
• What impact does a backup anchor have on safety during rope rescue?
• What should you avoid while washing a harness to prevent damage?
• What impact does the type of fiber have on Kernmantle rope?
• Are both high angle and low angle evacuations considered "technical rescue"? Why?
• What is meant by the term "track line" in a high line system?
• What does the term "Critical Angle" refer to?
• Which of the following is an example of a soft belay rope grab?
• What is the industry standard for the critical angle in anchor setups?
• On average, how much weight will a hauler pull before asking for help?
• What prompted the shift from natural fiber rope to synthetic rope?
• How does a Triple Wrapped Prusiks hitch function in self belay?
• Which knot is NOT commonly used for safety in rope applications?
• When utilizing a rope grab for positioning, what type is generally preferred for ease of adjustment?
• What is the purpose of a "High-Strength Tie Off"?
• What is a "Figure 8 Bend"?
• How does failure occur in rope due to abrasion?
• What purpose do festoons serve in a high line system?
• What are the two types of litter harnesses used in rescue operations?
• How is a Simple Pulley System defined?
• Why do rescue teams generally avoid using high lines?
• What is one functional advantage of using a spider (horizontal litter)?
• Where should you check for wear and tear on mechanical ascenders?
• Why are climber's swami belts and firefighters pompier belts not safe for rope rescue?
• What is the team capacity for a 3:1 ratio system in a high line rescue?
• What effect do sharp bends in a rope have on its strength?
• What is a significant risk when a carabiner is loaded with the gate open?
• When preparing for a vertical pick off, what is a critical positioning factor for the victim?
• Why is it important to understand the limits of a hauling system?
• What is the first critical step in a rescue operation?
• What is the gate of a carabiner?
• Do tandem prusiks need to be set up differently for raising versus lowering operations?
• When selecting a path to the subject, what should be avoided?
• What method can be employed to get a victim over a difficult edge during a rescue?
• Does NFPA 1983 require Block Creel construction for all life safety rope?
• Which type of system is a 6:1 mechanical advantage?
• How does NFPA classify equipment performance?
• What is the life span of life safety rope?
• What component can be an alternative to tandem prusiks for a hard mechanical belay rope grab?
• What issue arises from using a non-locking carabiner in certain climbing applications?
• What key advantage does Polyester Fiber rope offer regarding environmental factors?
• Why are high lines more prone to failure?
• What is the primary goal of the Access phase in the LAST format?
• What is a piggyback system in rescue operations?
• What does the 15:1 rule pertain to in rope rescue operations?
• How can a rescuer utilize their body weight effectively during a low angle rescue?
• Why is NFPA 1670 considered general in its contents?
• Is it possible to fully assess the situation before reaching the patient?
• Who is credited with developing the Brake Bar Rack?
• When instructed to "Faster," what action should be taken?
• What is the purpose of an edge pad?
• What is a primary purpose of a full body harness?
• Was the 15:1 ratio SSF intended to apply to the entire system?
• What determines how much stretch a Kernmantle rope will have?
• Which type of rescue rope provides a higher tensile strength?
• What is the preferred knot for tying a main line to a litter?
• According to NFPA 1983, attachment points on harnesses are designated as either ________ or ________.
• What are the primary lowering systems recommended for use?
• What does DCD stand for in the context of rope rescue?
• Why should a belay line not be put through a change in direction pulley?
• What is the kN tensile strength of General Use Life Safety Rope?
• What does "System On" indicate?
• What does "Faster" imply in the context of rope rescue commands?
• How does the angle of the load affect the performance of an anchor?
• Which equipment is primarily associated with the Tender System?
• What are considered weak parts of a carabiner?
• What characteristic of rectangular litters aids in their operational flexibility?
• What common mistake can lead to carabiner failure during a load?
• Which of the following describes technical use equipment according to NFPA 1983?
• Which of the following is included in the LAST acronym?
• What aspect of the major axis is important for carabiner safety?
• What is classified as Low Stretch Rope?
• What is the older term for a load distributing anchor system?
• What crucial aspect is associated with managing rope during descent?
• In a 2:1 system, how many people can be on the haul team?
• When connecting to the tender line of a litter, what should be done to the end of the line?
• When referencing the term "backed up" in anchors, what is primarily emphasized?
• Which aspect is crucial when tying a knot to a litter to distribute the load effectively?
• What are the two areas of friction in a pulley system?
• What is a helpful tool for estimating loads on highline systems in rope rescue?
• What is defined as a Bight in a rope?
• How does energy absorption relate to a rope's functionality?
• What does a "pretensioned back tie" help achieve?
• How does spreading the bars apart on a Brake Bar Rack affect descent speed?
• What does the term 'energy absorption' typically refer to in rope rescue operations?
• What is the recommended spacing between the main line and belay system?
• What is the term for a system where the DCD is attached to the litter harness?
• Which tool helps reduce the load during a low angle rescue and minimizes the number of tenders needed?
• What type of rope is recommended for use with the MPD device?
• Is it permissible to pretension and back tie an anchor that is outside the load force's vector?
• Does NFPA 1983 establish a 15:1 safety rating for all systems?
• How does increasing the angle of a high line affect the force on the anchors?
• What is a primary reason for using a litter during patient transport?
• Which standard provides the minimum job performance requirements for rescuers at various levels?
• What is a munter hitch primarily used for?
• What percentage of the load is typically carried by the core of Kernmantle rope?
• What is a litter?
• What occurs when a high line system is tensioned incorrectly?
• Which statement about litter harnesses is correct?
• What is the primary function of a Y-Lanyard/Bypass Lanyard in a rescue?
• Is it possible to straighten a minor bend in a steel anchor plate?
• Are plastic litters with a metal top rail suitable for rope rescue?
• What construction method is recommended for webbing intended for rescue applications?
• What is the primary advantage of a 1:1 system in rope rescue?
• Which offers more protection to the patient during transport?
• What aspect of teamwork is crucial for a rescue team's success?
• What is the main purpose of tending the prusiks during a lowering operation?
• Which method increases the overall strength of an anchor system?
• What is the primary function of pulleys in rope rescue operations?
• What is a characteristic feature of Kernmantle construction?
• What does the Rule of 18 refer to in high line operations?
• What is one main advantage of using Nylon rope?
• When managing a rescue from above, what should be taken into consideration?
• Which of the following is an implication of a Fall Factor greater than 1?
• What types of damage should you check for when inspecting a carabiner?
• What is a "Load Shearing Anchor"?
• What kind of conditions may require the use of a natural high directional during a rescue?
• During a rappelling operation, what two elements must a rescuer primarily manage?
• The system that involves a mechanics ratio where one can multiply the force applied while moving a load is known as?
• The analysis method that evaluates each component's potential failure impact is called?
• What is the main function of a stopper knot?
• What is the recommended method for washing a harness?
• Is the rescue operation considered complete once you have finished the Transport phase of the LAST method?
• At what angle does slope work and high angle rescue typically begin?
• How should rescuers prepare for an unexpected challenge during a rescue mission?
• What type of material is typically LESS effective for managing friction in a brake bar rack?
• What is the simplest way to free a stuck nut on a locking carabiner?
• What is a Self Belief in the context of rope rescue?
• What is a key advantage of locking carabiners?
• What does "On Belay" mean?
• If you pull 100lbs on a 3:1 system, what will be the output force?
• How much strength can be lost when a carabiner is loaded on the short (minor) axis?
• In a situation with a paraglider stuck in a tree, what is a recommended rescue strategy?
• Which factor contributes to the quality of Block Creel rope?
• How is Fall Factor defined?
• Can a single overhand knot be used as a safety knot in rope?
• What is a notable disadvantage of Polyester Fiber rope?
• Which standard outlines the specifications for life safety rope, harnesses, and hardware?
• How high should high line anchors be placed for optimal safety during a rescue?
• What is the key to alleviating time restraints and possible failures during high line setup?
• Which shape of carabiner is the strongest?
• Which side of the J-Frame brake bar rack do the bars pivot on?
• If you have only a double pulley, can it be used as a single pulley?
• What defines a compound pulley system?
• In rescue operations, how is a "desired height" for a victim determined during a pick off?
• What is the knot efficiency of a tensionless hitch?
• What command should be given to stop all movement?
• Which part of the brake bar rack allows for adjusting the rate of descent?
• What is an advantage of Polyester Fiber rope compared to Nylon?
• What are the three main risks to consider when performing a risk assessment during a rope rescue?
• What does a complete inspection of a rope include?
• At a critical interior angle of 120 degrees, the load on each anchor equals what percentage of the original load?
• What is a primary consideration to keep in mind when setting up a rescue system?
• Why is it important to keep a rappel line away from the subject?
• When ascending with Etriers, how can you prevent the loops from slipping off?
• What advantage does the offset-D (DNA) carabiner provide?
• Which of the following can be used as a ratchet in a rescue system?
• What is recommended to use as a haul cam: triple wrapped prusiks or a mechanical rope grab?
• What characterizes a Fall Factor of 2?
• Can an A Frame be set up after the system is created?
• What action should be taken with ropes that raise doubts about their integrity?
• Where should you tie to an anchor on a tall structure?
• What is the primary function of a braking device in a lowering system?
• What is a critical reason for pulling slack from the line during a raising operation?
• When should a Brake Bar Rack be replaced according to material loss?
• How does an Edge or Rope Guard differ from an edge pad?
• What does "Up Rope" mean?
• What is the proper way to wash a rope?
• What is a significant risk when not properly positioning a victim during a pick off?
• What is the function of a high directional anchor during a rescue?
• Can chemical lubricants be used on carabiners?
• How did WWII influence the development of synthetic rope?
• Can the creator of a system conduct a Safety Check on that system?
• What are tag lines used for in a rescue operation?
• What is the purpose of Escape use equipment as defined by NFPA 1983?
• What should you ask the patient when getting them into the litter during a low angle slope rescue?
• What must a rescuer control during a rappel pick off?
• Which of the following is NOT a goal of edge protection?
• What additional requirements are needed on the tensioning anchor side of a high line?
• What does the Whistle Test determine in a rope rescue system?
• How should ropes be dried after washing?
• What happens if more than 10% of the material is missing from a Brake Bar Rack?
• When passing a knot in the system on a raise, can the Dog and Tails knot be utilized?
• What does NFPA 1983 standardize for manufacturers?
• What should you avoid when connecting a subject to your harness during a rescue?
• What defines Static rope?
• Which method involves testing what the system does if all operators let go at once?
• Which analysis is NOT part of a Rope Rescue System Analysis?
• How does bending a rope affect its strength?
• What does NFPA 1983 classify as Technical use equipment?
• What does a primary factor in anchor effectiveness primarily depend on?
• When using pickets to create an anchor, at what angle should they be driven?
• Why is it important to use a load cell in a rope rescue system?
• What is a change of direction anchor?
• Which configuration allows multiple mechanical advantages to be achieved?
• Are life safety ropes classified based on their elongation under load?
• Which type of system are festoons specifically used in?
• When tying a figure 8 follow through, what is essential to ensure stability?
• What must be used to protect every raising system, regardless of complexity?
• In terms of rope performance, what design load was used to apply the 15:1 rule?
• During the setup of a rescue anchor, what should be done if the rope is at risk of abrasion?
• What is the Kern in Kernmantle rope?
• A device that holds the rope to prevent lowering when releasing the pulling force is called?
• How does increasing the length of rope affect the mechanical advantage?
• What is the best setting to develop new skills and evaluate team member capabilities?
• Which wrapping method is considered the strongest when using 1" webbing for an anchor?
• What method is more effective than increasing MA or adding more people to the haul team?
• A rescuer with a PT will give you about how many kN of load?
• What is the definition of a Fall Factor of 1?
• In climbing safety, what does redundancy refer to?
• Should the harness on the subject be connected to the system before the rescue begins?
• For securing a load in rope rescue, which knot is the best choice?
• How does the Static Safety Factor influence rescue operations?
• What is the purpose of a fixed pulley in a rescue system?
• What is referred to as the spine of a carabiner?
• What is the primary function of a tensioning anchor in a high line setup?
• When is tension on the far tag line increased during a highline operation?
• What is one of the primary rules when developing a rescue plan?
• What should you yell to let the belayer know you are going over the edge?
• What should be avoided as anchor points on buildings?
• When assessing the safety of a rescue system, what is the crucial element to evaluate?
• What does "On System" mean?
• What type of knot method is constrained in use on raising systems?
• Figure 8 descenders are preferred for what length of rappels?
• What elongation figures are manufacturers required to label ropes with, according to NFPA 1983?
• What is the most common simple pulley system used for rescue?
• What is the recommended action when a single anchor point is insufficient?
• Will a tandem prusik belay work effectively on both raising and lowering belay systems?
• What indicates that the Spanish windlass is tight enough during setup?
• What type of harness is classified as Class I?
• Can a dog and tails knot method be used to pass a knot on a raising system?
• In a rescue system, what component does the becket relate to?
• What must be ensured about each anchor in a twin tension system?
• What defines an independent belay system?
• When are tandem prusiks primarily used in a rescue operation?
• What should you connect the pickets with when creating an anchor?
• What is the benefit of a 3:1 pulley system over a 2:1 pulley system?
• What is the purpose of the White Board Analysis?
• What is a basic figure 8 most commonly used for?
• What is the first action to take when trying to gain access to the subject?
• What is a messenger line used for in high line operations?
• What is the name of the hook part of a carabiner?
• What is a system where a DCD is used at the anchor called?
• What is the knot efficiency of a water knot?
• What knot can be used to tie two ends of a rope into a Prusik?
• What are the goals of placing edge protection during a rescue operation?
• What is the primary advantage of using Static rope in rescue operations?
• What potential issue does a change of direction anchor pose?
• What does "Slow" mean when given as a command?
• What action is crucial when rescuing someone from an elevated position?
• In what situation might a screw link be preferred over a carabiner?
• What is a "Contingency Anchor System"?
• Why is the type of carabiner important in rescue situations?
• What action does "Down System" require from the team?
• In a 2:1 system, where is the mechanical advantage typically connected?
• What does the Tender System involve for ascending a main line?
• At a critical angle of 120 degrees, what is the force applied compared to the original load?
• What effect does the Brake Bar Rack have on the rope during use?
• Who is authorized to inspect ropes?
• If you are assigned to a belay line using tandem prusiks that is lowering, what is your responsibility?
• What should a team do after completing the transport phase in a rescue?
• What does the abbreviation “MA” stand for in the context of pulley systems?
• What is one advantage of constructing a twin tension system?
• Which litter type is specifically designed for sliding patients through tight spaces?
• How does NFPA 1983 define General use equipment?
• Which phase of the LAST method involves moving the subject to safety?
• In a rope rescue context, what does a "Slow" command indicate?
• According to NFPA 1983, what differentiates general and technical carabiners?
• What is typically the first clue when locating a subject for a rope rescue?
• What is the consequence of loading a Brake Bar Rack backwards?
• Can sharp spots on a Brake Bar Rack or Figure 8 descender be smoothed out?
• Which designation of equipment is primarily used for emergency egress in firefighting?
• What is the primary disadvantage of a traction rappel?
• What does "Belay On" mean?
• What does a Fall Factor of 0 indicate?
• Why do low angle evacuations typically require more than one tender?
• During a rescue, what key factor does the tensioning anchor rely on?
• How are Class II harnesses categorized?
• What should team members focus on during training rather than during rescues?
• What is the primary function of a "Travel Restraint System"?
• Which hitch is the preferred gripping or friction knot?
• Should a Safety Check be performed after modifications to a system?
• During a descent, what is the main purpose of a descender device?
• How should the Spanish windlass be secured when using it in a picket anchor system?
• If a track line fails, what is the maximum percentage the load can drop before being caught by the belay system?
• Which method should be used to tighten the rope connected to the pickets?
• What is a major limitation of not being able to honestly analyze performance in rescue training?
• Is there an NFPA standard for basket-type rescue litters?
• Where are 4:1 and 2:1 systems most commonly used?
• Where should the victim be positioned during a vertical pick off?
• What are the three designations of performance for equipment according to NFPA 1983?
• What type of loads are screw links best designed to perform under?
• Why are rectangular models of basket litters advantageous?
• What is the performance requirement for general use life safety rope as per NFPA 1983?
• For rescue or rappelling, which type of rope is preferred?
• How does a rescuer determine if a situation requires a high angle or low angle evacuation?
• What characteristic differentiates rappel gloves from regular store gloves?
• What is the knot efficiency of a "High-Strength Tie Off"?
• What does "Rope Free" indicate?
• In high-angle rescue, what is the essential consideration when selecting an anchor point?
• What is the purpose of a litter shield?
• What is another name for a Progress Capture Device?
• Can an AZTEK system be effectively used to connect a rescuer to a litter?
• What should be done after accessing the subject during a rescue?
• Are fittings for window washing on high-rise buildings suitable as anchor points?
• What happens when webbing is created with a shuttle loom?
• What is the purpose of a belay in rope rescue operations?
• What could potentially happen if high lines are not well-managed?
• What type of anchor is primarily created when freeing a victim from a caged industrial ladder?
• What advantage does a full body harness have over a sit harness?
• What is the recommended sheave diameter in relation to the rope diameter to minimize strength loss?
• When raising with tandem prusiks, what should you focus on with the prusiks?
• For a 6:1 ratio system, what is the maximum number of people allowed on the haul team?
• What is the primary purpose of NFPA 1670?
• What happens to a prusik cord when it is overloaded with the right sized cord?
• What does giving the command "Stop" mean in a rescue operation?
• What effect does increased twisting of the core bundles have on a Kernmantle rope?
• Does a nationally recognized certification for rope rescue instructors currently exist?
• Figure 8 descenders are most suitable for which type of load?
• What should everyone carry in their pocket when working with ropes?
• What is the name of the pulley that increases the mechanical advantage of a system while moving?
• What does it mean for an anchor to be backed up?
• Where should ropes and rope bags be stored to maintain their condition?
• What defines an anchor point in rope rescue?
• How should a Class II and III harness be drop tested?
• What does NFPA 1983 specifically state about the certification of equipment?
• What is the basis for ascending systems employed by Rope Access Technicians?
• What disadvantage of Nylon rope can occur when exposed to moisture?
• What is the kN tensile strength of Technical Use Life Safety Rope?
• When positioning closer to a victim using an AZTEK, what additional equipment is used?
• Which anchor system relies on the length of the legs for load distribution?
• What should you be cautious about when using a pretensioned back tie?
• How should an anchor ideally be set up?
• Who has the authority to give the command "Stop" during a rescue operation?
• Which of the following is NOT a risk factor for a mechanical rope grab?
• What happens to the load on the anchor when the critical angle increases?
• What type of harness is needed for the Frog Ascending System?
• When should ropes be inspected for safety?
• How does leaning back into the harness assist during a rescue operation?
• Why must the haul team be cautious when increasing mechanical advantages?
• Which knot is known for its ability to hold well under load but untie easily after use?
• Which type of rope construction is most commonly used in current rescue operations?
• Which aspect is crucial for the knot efficiency of a tensionless hitch?
• What is the primary purpose of an A Frame?
• What is the purpose of the ears on figure 8 descenders used by rescue teams?
• What do you need more of when increasing the mechanical advantage (MA)?
• What is the function of the positioning loop in an AZTEK system?
• How is the Static Safety Factor (SSF) of a system determined?
• Which knot passes through a knot pass pulley easier?
• Why is it important to keep track of a rope's history?
• What does the LAST format help to achieve in a rescue situation?
• Why is it essential for a rescuer to manage descent during a pick off?
• What is characterized as "Block Creel" rope construction?
• In the context of a high directional anchor, where is the anchor typically placed during rescue operations?
• Does NFPA 1983 mandate the use of steel carabiners for fire departments?
• What is the primary concern with using rope that has a questionable history?
• What critical feature should a tag line possess during a high line operation?
• What type of device is essential in a lowering system connected to an anchor?
• What are some alternative names for a water knot?
• Which statement accurately describes the absorption properties of Nylon rope?
• In the context of rope strength, what happens with sharper bends in the rope?
• What knot is the same as a figure 8 on a bite but is used to tie around an object and make an anchor?
• What term describes the rope systems suspended between two points that are used for moving people or equipment?
• What is a crucial factor influencing the force exerted on anchors in a high line system?
• What load capacity are mechanical ascenders designed to hold while ascending?
• Do carabiners need to be dry before storage?
• Which component on a figure 8 descender stops the rope from sliding and forming a knot?
• Why is regular training emphasized for rescue teams operating high lines?
• In what scenario would a litter shield be most effective?
• What is the purpose of a pulley system in rope rescue?
• What advantage does standardizing a team’s rescue system offer to new students?
• What feature makes a pulley prusik minding?